- Feb 25, 2022
Molybdenum Wire And EDM Gel Are The Guarantee of Surface Finish for Ultra-high Thickness Cutting
PRODUCTS USED IN THIS TEST:
- EDM MOlybdenum Wire φ0.22mm (TAGUTI Brand)
- JR-3A EDM Gel
Ultra-high thickness cutting is the advantage of high-speed WEDM. At present, it is not very difficult to cut ultra-high thickness (>1000mm) workpieces. The difficulty lies in how to stably cut for a long time and ensure the finish of the cutting surface of the workpiece. This test uses the upgraded JR-3A EDM Gel and the TAGUTI brand EDM Molybdenum Wire with characteristics of high purity, high strength and low elongation, which started in 1997.
1. Reasons for poor surface finish
During the ultra-high thickness cutting, the rigidity of the molybdenum wire decreases due to the substantial increase in length of it in the processing. In addition, it is difficult for EDM Gel to enter the bottom of the slit, resulting in a great difference between the discharge state between the electrodes during ultra-high thickness cutting and general thickness cutting. During the ultra-high thickness cutting, the processing stability is much lower than that of general thickness cutting, the vibration of molybdenum wire increases greatly. Therefore, although the workpiece can be cut, the stripes shown in Figure 1 often appear on the surface of workpiece. In particular, deep and dense stripes are formed at the upper and lower ends of the workpiece, which seriously reduce the surface quality of the workpiece, the depth of the stripes is between 0.01-0.1mm, or even deeper.
Figure 1 - Overall and partial photos of the workpiece with a thickness of 1500mm
In order to intuitively explain the reasons for the formation of stripes, the molybdenum wire feeding model shown in Figure 2 was established. Figure 2(a) is the theoretical feed path, but when the molybdenum wire vibrates, due to the low rigidity of it, a slight disturbance will deviate from the theoretical feed direction, so the feed does not strictly follow the theoretical straight line direction. Instead, the discharge is oscillated in a predetermined direction, as shown in Figure 2(b), then vibration fringes will be generated on the workpiece surface.
(a) Molybdenum wire theoretical feed path
(b) Feed path when the molybdenum wire vibrates
Figure 2 - Feeding Model of Interpole Molybdenum Wire during Ultra-high Thickness Cutting
2. Internal and external factors affecting cutting stability
EXTERNAL FACTORS:
During ultra-high thickness processing, in order to get a relatively flat surface, the stability of the molybdenum wire between the poles must be maintained. The customary practice is to use new molybdenum wire, new EDM Gel, and use constant tension mechanism, EDM Guide Wheel, and EDM wire guide to improve the stability of molybdenum wire. The EDM wire guide is mainly used to cut off the path of the vibration caused by the runout of the EDM guide wheel and the bearing and the change of the molybdenum wire tension to the processing area, as shown in Figure 3(a). After passing it, the vibration of the molybdenum wire due to the guide wheel and bearing will be greatly attenuated.
INTER FACTORS:
During the ultra-high thickness cutting, the vibration of the molybdenum wire caused by the discharge explosion force in the narrow and long processing area is the internal factor that affects the processing stability. For general EDM Gel, it is impossible to completely fill the narrow and long slit of the workpiece. Even if the slit can be filled, there will be a lot of vaporization under the action of high discharge temperature. Then in the second half of the slit, the EDM Gel will be greatly reduced, or even gone, so it cannot form a better and uniform damping and vibration-absorbing effect on the vibration of the molybdenum wire throughout the slit.
(a) General EDM Gel isn’t full of the slit
(b) Upgraded EDM Gel is full of slit
Figure 3 - Schematic diagram of vibration of molybdenum wire between electrodes during ultra-high thickness cutting
3. Conditions that guarantee the surface finish of workpiece
a. It must ensure that the slit is evenly filled with EDM Gel so that the vibration of the molybdenum wire can be evenly damped and absorbed in the entire narrow slit, as shown in Figure 3(b). To ensure that the slit is evenly filled with EDM Gel, the following points need to be done. Firstly, EDM Gel needs to have good cooling, washing, and deionization properties, and can be brought into the slit with molybdenum wire; secondly, the discharge gap should be enlarged as much as possible, so that EDM Gel can easily enter the slit, in order to obtain a wider discharge gap, it needs to appropriately increase the conductivity of EDM Gel, the no-load voltage, and the energy.
b. Due to the longer distance for chip removal of corrosion products, even if EDM Gel has filled the narrow and long slit,when cutting ultra-thick workpieces, it is necessary to reduce the vaporization of EDM Gel as much as possible and increase the proportion of high melting point and vaporization point components in EDM Gel to ensure that there is enough chip removal power to take out the erosion products. Figure 4 is a model diagram of the inter-pole state of different EDM Gels.
As shown in Figure 4(a), because of the narrow slit, the amount of general EDM Gel that can enter the slit is relatively small, and it is continuously vaporized in the narrow and long slit, so that it cannot have a damping and vibration-absorbing effect on the molybdenum wire; in addition, the ability to carry discharge erosion particles to discharge the workpiece is greatly reduced, and a large amount of erosion products will accumulate in the lower part of the slit, resulting in unstable processing.
The JR-3A EDM Gel with higher conductivity and added components with high melting point and vaporization point solves this problem in a targeted manner. Since a wider discharge gap can be obtained, the amount of working fluid that enters the slit with the molybdenum wire will increase, so in the narrow and long slit, it can have a good damping and vibration absorption effect on molybdenum wire. In addition, due to the components of high melting point and vaporization point in the working liquid increase, the chip removal power is greatly improved, and the corrosion products can be smoothly discharged from the slit, which further enhances the cutting stability. The schematic diagram between the poles is shown in Figure 4(b).
After the conductivity of EDM Gel increases, the leakage current will increase and consume part of the discharge energy. At the same time, the increase of the discharge gap will also reduce the cutting speed per unit current. However, because cutting stability is a crucial condition to ensure the smoothness of the cutting surface, the pursuit of cutting stability is the most important goal. In addition, the JR-3A EDM Gel can use a larger current for cutting, so the absolute cutting speed of the machine tool is not reduced.
(a) Interpolar state of general EDM Gel and corrosion products carried by it
(b) Interpolar state of upgraded EDM Gel and corrosion products carried by it
Figure 4- Interpolar state of different EDM Gel and corrosion products carried by it
